News | January 26, 1999

Tomography Provides 3-D images of IC Interconnects

By Yvonne Carts-Powell

Contents


  • How

  • Synch bye bye

  • Reference
  • Two-dimensional imaging is undeniably useful for finding faults in integrated circuits but for peering into the intricate depths of multilevel ICs, three-dimensional methods are vital. A group of researchers recently imaged an IC interconnect—a premier example of a 3-D structure—at a resolution of 400 nm [1] Researcher Zachary Levine at NIST (Gaithersburg, MD) and others at Rensselaer Polytechnic Institute (RPI, Troy, NY), Argonne National Laboratory (Argonne, IL), and Digital Equipment Corp. (Hudson, MA) used scanned X-ray nanotomography to obtain 3-D images from an aluminum-tungsten interconnect (see Figure). The sample was scanned across a 200-nm focal spot of 1573 eV radiation from the Advanced Photon Source synchrotron at Argonne National Laboratory. While synchrotron radiation is necessary at this point, laser plasma sources might eventually be usable, turning the method into a viable industrial tool for early production or failure analysis.

    Tomographic image of an integrated circuit. The isolated blobs are focused ion beam markers. Metal wires are visible to the left, and the vias are short protruding segments.

    Alternatives (back to top)
    Transmission electron microscopy (TEM) can provide 3-D images of integrated circuits, but its high resolutions (smaller than a nanometer) and small fields of view make it too fine a tool for applications such as multilayer interconnects. TEM samples are typically thinned to 200 nm, although high-voltage TEMs can image through a micron or two. In contrast, multilayer interconnects tend to be 5 to 15 micron thick. This is far too deep for TEM, but scanned X-ray tomography can image through this depth.

    A larger-resolution, larger field-of-view method is also needed to image flaws in logic circuits. Because logic circuits are irregular, the flaws cannot be localized as easily as in memory circuits, and thus the desired field of view is larger.

    How (back to top)
    The researchers imaged a three-level IC in which two levels of aluminum wires are connected by tungsten vias inside the silica, and several focused ion beam markers are embedded in the surface. A 250-micron-diameter region of the standard silicon 3-mm wafer was thinned to about 10 micron. Once the sample was in the beam, x-rays passing through the sample were detected with an avalanche photodiode. A raster scan of the sample used 301 ´ 301 pixels in nominally 50-nm steps. Thirteen images were obtained, each at a slightly different angle to the beam, then aligned to create a 3-D reconstruction.

    Synch bye bye (back to top)
    "X-ray tomography has the potential to be a useful research tool for ICs, particularly for fault analysis," says Waleed Haddad of Lawrence Livermore National Laboratory. "But for it to be a manufacturing tool really major advances, at least in light sources," must occur. Levine explains: laser plasma sources are lab-sized devices that generate x- rays, but they emit in all directions, unlike the focusable beam produced by a synchrotron. If the optics for these laser plasma sources could gather and focus the radiation, then they might be a feasible source.

    Levine says, "If you could get within a factor of five of the theoretical limit of a Wolter optic, then you could get off the [synchrotron] ring." Then chip-makers could afford in-house instruments. Haddad adds, "It comes down to speed and the cost to acquire data." Dependence on a synchrotron severely limits the throughput of samples.

    For now, the researchers are focused on improving the resolution of their system. The next run will attempt to show a 150 nm resolution. Because quarter-micron feature devices are already in production, the resolution will have to be even smaller than that to show the shapes of the wires. Levine says, "we want 50-nm resolution."

    Reference (back to top)
    [1] Zachary Levine, et. al., Applied Physics Letters 74(1), 4 Jan 99, p. 150. (back to article)

    About the author
    Yvonne Carts-Powell is a freelance writer based in Massachusetts. (back to top)